Recycling of polymer materials using ethylene vinyl acetate and styrene block copolymer
https://doi.org/10.35164/0554-2901-2022-3-4-43-45
Abstract
The technology for obtaining highly filled composite materials based on ethylene vinyl acetate (EVA) and styrene block copolymer (SBS) is presented. Crumb rubber from recycling tires was used as a filler. The working temperature of rubber crumb activation has been determined, namely, the vulcanization temperature of the non-crosslinked part is 170°C. The amount of noncrosslinked part in the rubber crumb was established to be not less than 2%.
About the Authors
I. E. MZHACHIKH
Federal State Budgetary Educational Institution of Higher Education Dmitry Mendeleev University of Chemical Technology of Russia (Mendeleev University of Chemical Technology)
Russian Federation
Russian Federation
Moscow
N. V. KOSTROMINA
Federal State Budgetary Educational Institution of Higher Education Dmitry Mendeleev University of Chemical Technology of Russia (Mendeleev University of Chemical Technology)
Russian Federation
Russian Federation
Moscow
T. P. KRAVCHENKO
Federal State Budgetary Educational Institution of Higher Education Dmitry Mendeleev University of Chemical Technology of Russia (Mendeleev University of Chemical Technology)
Russian Federation
Russian Federation
Moscow
I. YU. GORBUNOVA
Federal State Budgetary Educational Institution of Higher Education Dmitry Mendeleev University of Chemical Technology of Russia (Mendeleev University of Chemical Technology)
Russian Federation
Russian Federation
Moscow
References
1. Долинская Р.М., Прокопчук Н.Р. Рециклинг отходов резинотехнических изделий (обзор) // Полимерные материалы и технологии. 2020. Т. 6. №1. С. 6-24.
2. Fazli A., Rodrigue D. Waste Rubber Recycling: A Review on the Evolution and Properties of Thermoplastic Elastomers // Materials. 2020. N13 (3). P. 782-813.
3. Каблов В.Ф., Перфильев А.В., Шабанова В.П., Перфильев А.А. Альтернативная технология изготовления резиновых изделий из продуктов рециклинга автомобильных шин // Каучук и резина. 2017. Т. 76. №3. С. 172-175.
4. Kakroodi A.R, Rodrigue D. Highly filled thermoplastic elastomers from ground tire rubber, maleated polyethylene and high density polyethylene // Plastics Rubber and Composites. 2011. Vol. 42. N3. P. 115-122.
5. Kontareva T.A., Kechek'yan A.S., Sinevich E.A., Serenko O.A. Features of the deformation behaviour of particulatefilled composites based on polyethylene and rubber particles at elevated temperatures // International Polymer Science and Technology. 2014. Vol. 41. N2. P. 37-44.
6. Костромина Н.В., Борисова В.С., Ивашкина В.Н., Осипчик В.С. Исследование высоконаполненных композиционных материалов на основе термопластов // Успехи в химии и химической технологии. 2014. Т. 28. №3 (152). С. 34-37.
7. Контарева Т.А., Гончарук Г.П., Оболонкова Е.С., Серенко О.А. Влияние свойств матричного полимера на деформационные характеристики дисперсно-наполненных композитов на основе полиэтилена и частиц резины // Журнал прикладной химии. 2012. Т. 85. №5. С. 799-804.
8. Контарева Т.А., Александров А.И., Кечекьян А.С., Оболонкова Е.С., Серенко О.А. Механизм разрушения высоконаполненных композитов на основе полиэтилена и частиц резины // Механика композиционных материалов и конструкций. 2013. Т. 19. №2. С. 154-162.
9. Jiang Tao Zhang, Song Dan Ping, Zhang Me, Zhai Peng Cheng. Microstructure Deformation and Fracture Mechanism of Highly Filled Polymer Composites under Large Tensile Deformation // Journal of Physics Conference Series. 2014. Vol. 419. N 1. P. 123-131.
Review
For citations:
MZHACHIKH I.E., KOSTROMINA N.V., KRAVCHENKO T.P., GORBUNOVA I.Yu. Recycling of polymer materials using ethylene vinyl acetate and styrene block copolymer. Plasticheskie massy. 2022;(3-4):43-45. (In Russ.) https://doi.org/10.35164/0554-2901-2022-3-4-43-45
Views:
372
Email this article 
