Preview

Plasticheskie massy

Advanced search

Investigation of the rheological behavior of ABS plastic grades for the production of filaments for 3D printing by layer-by-layer deposition

https://doi.org/10.35164/0554-2901-2021-5-6-29-35

Abstract

A comprehensive study of the rheological properties of ABS-plastic grades used for the manufacture of fi laments for 3D printing by the FDM method has been carried out. It is shown that under the printing temperature-speed conditions, the viscous properties of melts of different grades and activation energy of their viscous flow differ significantly. The temporal parameters of the thermal stability of melts at an elevated (250°C) temperature were determined by the rheological method. It is shown that, under printing conditions, the polymer does not undergo noticeable degradation, assessed by the change in its effective viscosity. Viscoelasticity, which determines the dimensional accuracy of products and the thickness of the deposited layer, was evaluated by the degree of swelling of the extrudate under different flow conditions. Criteria for the applicability of ABS-plastic grades for fi lament production are proposed.

About the Authors

O. I. Abramushkina
JSC "Interindustry Institute of Plastics Processing - NPO "Plastic"
Russian Federation


M. I. Uzorina
MIREA - Russian Technological University (Institute of Fine Chemical Technologies named after M.V. Lomonosov)
Russian Federation


P. V. Surikov
MIREA - Russian Technological University (Institute of Fine Chemical Technologies named after M.V. Lomonosov)
Russian Federation


O. B. Ushakova
MIREA - Russian Technological University (Institute of Fine Chemical Technologies named after M.V. Lomonosov)
Russian Federation


References

1. FDM 3D printing materials compared: [электронный ресурс]. URL: https://www.3dhubs.com/knowledge-base/fdm-3d-printing-materials-compared. (Дата обращения 01.07.2021).

2. Molecular structure and design of thermoplastic polymers for 3D printing. By Tosca van Hooy, Zuyd University of Applied Sciences, The Netherlands and Varun Srinivas, Dietmar Auhl, and Jules Harings, Maastricht University, The Netherlands. : [электронный ресурс]. URL:https://www.zuyd.nl/binaries/content/assets/zuyd/onderzoek/interviews--artikelen/material-sciences_research-paper_3d-fab-print.pdf. Дата обращения 01.07.2021.

3. Реологические свойства термопластичной композиции на основе поликарбоната: зависимость от температуры переработки; влияние на механические характеристики и размерную стабильность объектов, созданных по FDM-технологии. Петрова Г.Н. и др. // Труды ВИАМ, №4 (52), 2017.

4. Коваленко Р.В. Современные полимерные материалы и технологии 3D печати. Вестник технологического университета. 2015, т.18, в.1, с.263–266.

5. Pritish Shubham, Arnab Sikidar and Teg Chand. The Infl uence of Layer Thickness on Mechanical Properties of the 3D Printed ABS Polymer by Fused Deposition Modeling. Key Engineering Materials, 706, August, 2016, P. 63–67.

6. Jason Cantrell and others. Experimental Characterization of the Mechanical Properties of 3D-Printed ABS and Polycarbonate Parts: [электронный ресурс]. URL: https://mae.ufl.edu/rapidpro/pages/3D%20Printing%20Paper%20Final%20Manuscript.pdf (Дата обращения 02.07.2021).

7. Gordeev E.G., Galushko A.S., Ananikov V.P. Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling. PLOS ONE 13(6), 2018: e0198370: [электронный ресурс]. URL: https://journals.plos.org/plosone/article?id=10.1371/journal.pone.0198370. (Дата обращения 02.07.2021).

8. Mohammed Elbadawi. Polymeric Additive Manufacturing: The Necessity and Utility of Rheology: [электронный ресурс]. URL: https://www.intechopen.com/books/polymer-rheology/polymeric-additive-manufacturing-the-necessity-and-utility-of-rheology. (Дата обращения 02.07.2021).

9. Каталог ООО «Руспласт»: [электронный ресурс]. URL: https://rusplast.com/catalog/abs-plastic. (Дата обращения 02.07.2021)

10. Сайт АО «Пластик»: [электронный ресурс]. URL: http://oaoplastic.ru/products/abs-plastics. (Дата обращения 02.07.2021)

11. Эл. ресурс https://wiki.e3d-online.com/images/3/3a/V6-NOZZLEALL.pdf.

12. Калинчев Э.Л., Саковцева М.Б. Свойства и переработка термопластов. - Л.: Химия, 1983 - 288 с.

13. Мендельсон Р., Фингер Ф., Бэгли Е. Разбухание струи и обратимые сдвиговые деформации при экструзии полиэтилена. - В кн.: Вязкоупругая релаксация в полимерах.- М.: Мир, 1974, С. 178-191.


Review

For citations:


Abramushkina O.I., Uzorina M.I., Surikov P.V., Ushakova O.B. Investigation of the rheological behavior of ABS plastic grades for the production of filaments for 3D printing by layer-by-layer deposition. Plasticheskie massy. 2021;(5-6):29-35. (In Russ.) https://doi.org/10.35164/0554-2901-2021-5-6-29-35

Views: 429


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 0554-2901 (Print)